Below is a sample of XC03 book II, aka, an MCC script for a Phase I and Phase II measurement. Following that is a sample of the log file generated and stored by the MCC scripting tool.
*************************************************
*********** Phase I Measurement ***************
*************************************************
write all --####### Start of Measurement LHS-PI-1.004 #######
write all LHS-PI-1.004 is a PSF/Inner Core measurement 10000 second duration.
write dlrs MEAS_SETUP TRW-ID LHS-PI-1.004
--XSS Setup
write XSS Gen 01 Configure EIPS to run Mg-Ka (6.4,140.217)
write XSS Filter 02 Filter 1 N/AThick N/A Filter 2 Mg Thick 47.2.
-- EKC setup
write EKC 100 Orientation Move HRMA to (0,0).
write EKC 101 OTG InsertLETG
-- SAO Setup
write SAO 203 BND BND-H in fixed mode. Integration time 10000
write SAO 204 HSA configuration to be all blades open.
write SAO XSS Config EIPS to run Mg-Ka set volt to 6.4 with curr 140.217
write SAO XSS Filter 02 Filter 1 N/A Thick N/A Filter 2 Mg Thick 47.2.
-- Ball Setup
write BALL 300 SIM-Z -250.1
write BALL 301 FAM Position {0,0,0,0,0,0}.
write BALL 302 Start dither using file letg_hrcs_psf
-- FPSI Setup
write HRC 500 HRC image(dum1,dum2,dum3,dum4)
-- wait for ready signal(CTUE Format note in DLRS)
Stop
write all Everyone ready for LHS-PI-1.004
write SAO 205
HSA Open Shutter
-- wait for shutter open
stop
-- give warning to FPSI
write all measurement to begin in 5 seconds.
delay 5
write SAO 206 BND Start BND
stop
--place flag when BND is started
write dlrs MEAS_START LHS-PI-1.004
write all Measurement LHS-PI-1.004 underway, 10000 sec.
--Delay to be clocked by Test Conductor dd:hh:mm:ss:dddd
stop
write HRC specifed measurement time completed
stop
write all collection period for LHS-PI-1.004 complete
write SAO 207 BND Stop BND
stop
write dlrs MEAS_STOP LHS-PI-1.004
write SAO 208 HSA Close all shutters
Stop
write BALL 305 Stop Dither
write XSS 03 clean up from measurement LHS-PI-1.004
write EKC 103 clean up from measurement LHS-PI-1.004
write SAO 210 clean up from measurement LHS-PI-1.004
write Ball 303 clean up from measurement LHS-PI-1.004
write HRC 502 clean up from measurement LHS-PI-1.004
stop
write dlrs MEAS_CLND LHS-PI-1.004
write all -- *****End of Measurement LHS-PI-1.004 #####
*************************************************
*********** Phase II Measurement **************
*************************************************
write all --******Start of IXS-EE-1.007 *******
write dlrs MEAS_SETUP IXS-EE-1.007
write all This measurement is an encircled energy measurement. Duration T seconds.
--XSS Setup
write XSS 01 Configure EIPS to run Mg-Ka set voltage to 6.4 with current 140.217
write XSS 02 Filter 1 N/AThickness N/A Filter 2 Mg Thickness 47.2.
-- EKC Setup
write EKC 100 HRMA Orientation Move HRMA to (0,0).
write EKC 101 Gratings No OTG in Place
-- SAO Setup
write SAO 200 Setup for IXS-EE-1.007
write SAO XSS Setup Configure EIPS to run Mg-Ka set voltage to 6.4 with current 140.217
write SAO XSS Filter Setup Filter 1 N/AThickness N/A Filter 2 Mg Thickness 47.2.
-- End setup wait for ready messages
Stop
write all Everyone is ready for IXS-EE-1.007
Stop
write all Beginning IXS-EE-1.007
-- Start measurement IXS-EE-1.007
write dlrs MEAS_START IXS-EE-1.007
write all Measurement IXS-EE-1.007 underway, duration T
write SAO 201 Commence measurement IXS-EE-1.007
-- Wait for finished signal from SAO
Stop
wr
ite all Measurement IXS-EE-1.007 completed.
write dlrs MEAS_STOP IXS-EE-1.007
write XSS 03 clean up from measurement IXS-EE-1.007
write EKC 103 clean up from measurement IXS-EE-1.007
write SAO 210 clean up from measurement IXS-EE-1.007
write Ball 303 clean up from measurement IXS-EE-1.007
write HRC 502 clean up from measurement IXS-EE-1.007
write dlrs MEAS_CLND IXS-EE-1.007
Stop
write all --******End of IXS-EE-1.007 *******
*************************************************
*************** Script Log ********************
*************************************************
This is a capture of us doing a lot of hacking and
testing; don't expect it to match the above scripts
exactly.
150/15:29:28 XSS tc_p YOU THERE?
150/15:29:35 tc XSS Yes
150/15:33:51 sstmgr tc XRCF logged in
150/15:35:55 sstmgr tc EKC logged in
150/15:36:52 sstmgr tc SAO logged in
150/15:37:24 sstmgr tc CTUE logged in
150/15:38:48 sstmgr tc ACIS logged in
150/15:39:29 sstmgr tc HRC logged in
150/15:39:53 sstmgr tc BALL logged in
150/15:47:15 tc dlrs MEAS_SETUP IXS-EE-1.007
150/15:47:16 tc all Measurement IXS-EE-1.007
150/15:47:17 tc all This measurement is an encircled energy measurement.
Duratio
n T secon
150/15:47:39 tc XSS Generator 01 Configure EIPS to run Mg-Ka set voltage
to 6.4 with curr
150/15:47:42 tc XSS Filter 02 Filter 1 N/AThickness N/A Filter 2 Mg Thic
kness 47.2.
150/15:47:45 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
150/15:47:46 tc EKC 101 Gratings No OTG in Place
150/15:47:47 tc SAO 200 Setup for IXS-EE-1.007
150/15:47:48 tc SAO XSS Setup Configure EIPS to run Mg-Ka set voltage to
6.4 with current
150/15:47:55 tc SAO XSS Filter Setup Filter 1 N/AThickness N/A Filter 2
Mg Thickness 47.
150/15:48:32 sstmgr tc XSS logged in
150/15:50:05 tc dlrs MEAS_SETUP IXS-EE-1.007
150/15:50:06 tc all Measurem
ent IXS-EE-1.007
150/15:50:08 tc all This measurement is an encircled energy measurement.
Duration T secon
150/15:50:17 tc XSS Generator 01 Configure EIPS to run Mg-Ka set voltage
to 6.4 with curr
150/15:50:21 tc XSS Filter 02 Filter 1 N/AThickness N/A Filter 2 Mg Thic
kness 47.2.
150/15:50:22 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
150/15:50:23 tc EKC 101 Gratings No OTG in Place
150/15:50:24 tc SAO 200 Setup for IXS-EE-1.007
150/15:50:25 tc SAO XSS Setup Configure EIPS to run Mg-Ka set voltage to
6.4 with current
150/15:50:28 tc SAO XSS Filter Setup Filter 1 N/AThickness N/A Filter 2
Mg Thickness 47.
150/15:52:03 XSS tc got 01
150/15:52:38
EKC tc got 100,101
150/15:54:38 SAO tc got 200
150/15:55:59 tc XSS Filter 02 Filter 1 N/AThickness N/A Filter 2 Mg Thic
kness 47.2.
150/15:57:09 XSS tc got 02
150/15:58:17 XSS tc did 01
150/15:58:47 XSS tc did 02
150/15:59:16 EKC tc did 100,101
150/15:59:27 SAO tc did 200
150/16:02:25 tc all Everyone is ready for IXS-EE-1.007
150/16:02:36 tc all Beginning IXS-EE-1.007
150/16:02:37 tc dlrs MEAS_START IXS-EE-1.007
150/16:02:38 tc SAO 201 Commence measurement IXS-EE-1.007
150/16:03:25 SAO tc got 201
150/16:05:26 SAO tc did 201
150/16:09:31 tc all Measurement IXS-EE-1.007 completed.
150/16:09:32 tc dlrs MEAS_STOP IXS-EE-1.007
150/16:09:33 tc all Clean up from IXS-EE-1.007
150/16:09:34 tc dlrs MEAS_CLND IXS-EE-1.007
150/16:10:37 tc dlrs we are repeating this measurement for purposes of th
inking about procP
150/16:10:49 tc dlrs MEAS_SETUP IXS-EE-1.007
150/16:10:50 tc all Measurement IXS-EE-1.007
150/16:10:51 tc all This measurement is an encircled energy measurement.
Duration T secon
150/16:10:58 tc XSS Generator 01 Configure EIPS to run Mg-Ka set voltage
to 6.4 with curr
1
50/16:11:04 tc XSS Filter 02 Filter 1 N/AThickness N/A Filter 2 Mg Thic
kness 47.2.
150/16:11:05 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
150/16:11:06 tc EKC 101 Gratings No OTG in Place
150/16:11:07 tc SAO 200 Setup for IXS-EE-1.007
150/16:11:08 tc SAO XSS Setup Configure EIPS to run Mg-Ka set voltage to
6.4 with current
150/16:11:10 XSS tc got 01
150/16:11:20 EKC tc got 100,101
150/16:11:30 EKC tc did 100,101
150/16:11:37 XSS tc did 01
150/16:11:37 tc XSS Filter 02 Filter 1 N/AThickness N/A Filter 2 Mg Thic
kness 47.2.
150/16:11:48 SAO tc got
200
150/16:11:53 SAO tc did 200
150/16:18:21 tc all Everyone is ready for IXS-EE-1.007
150/16:18:30 tc all Beginning IXS-EE-1.007
150/16:18:31 tc dlrs MEAS_START IXS-EE-1.007
150/16:18:32 tc SAO 201 Commence measurement IXS-EE-1.007
150/16:19:28 SAO tc got 201
150/16:19:34 SAO tc did 201
150/16:20:07 tc all Measurement IXS-EE-1.007 completed.
150/16:20:13 tc dlrs MEAS_STOP IXS-EE-1.007
150/16:20:19 tc all Clean up from IXS-EE-1.007
150/16:20:25 tc dlrs MEAS_CLND IXS-EE-1.007
150/16:20:43 tc SAO XSS Filter Setup Filter 1 N/AThickness N/A Filter 2
Mg Thickness 47.
150/16:20:53 tc all Everyone is ready for IXS-EE-1.007
150/16:20:58 tc all Beginning IXS-EE-1.007
150/16:22:31 tc all Everyone is ready for IXS-EE-1.007
150/16:22:40 tc all Beginning IXS-EE-1.007
150/16:22:41 tc dlrs MEAS_START IXS-EE-1.007
150/16:22:42 tc SAO 201 Commence measurement IXS-EE-1.007
150/16:23:43 tc all Beginning IXS-EE-1.007
150/16:23:44 tc dlrs MEAS_START IXS-EE-1.007
150/16:23:45 tc SAO 201 Commence measurement IXS-EE-1.007
150/16:24:16 tc all Everyone is ready for IXS-EE-1.007
150/16:24:20 tc all Beginning IXS-EE-1.007
150/16:24:21 tc dlrs MEAS_START IXS-EE-1.007
150/16:24:22 tc SAO
201 Commence measurement IXS-EE-1.007
150/16:26:18 tc all we will now do a Phase II measurement.
150/16:27:26 tc all Measurement LHS-PI-1.004
150/16:27:30 tc all LHS-PI-1.004 is a PSF/Inner Core measurement 10000 s
econd duration.
150/16:27:31 tc dlrs MEAS_SETUP TRW-ID LHS-PI-1.004
150/16:27:32 tc dlrs LHS-PI-1.004 is a PSF/Inner Core measurement.
150/16:27:33 tc EKC 100 Orientation Move HRMA to (0,0).
150/16:27:34 tc EKC 101 OTG InsertLETG
150/16:27:35 tc SAO 203 BND BND-H in fixed mode, not synchronized to ACI
S. Integration ti
150/16:27:40 tc SAO 204 HSA All blades open.
150/16:27:44 tc BALL 300 SIM-Z -250.1
150/16:27:45 tc BALL 301 FAM Position {0,0,0,0,0,0}
.
150/16:
27:46 tc BALL 302 Dither file letg_hrcs_psf
150/16:27:47 tc HRC Take HRC Image. Duration 10000
150/16:28:51 EKC tc got 100,101
150/16:29:00 EKC tc did 100,101
150/16:30:08 SAO tc got 203,204
150/16:30:30 SAO tc did 203,204
150/16:31:09 BALL tc got 300,301,302
150/16:31:20 BALL tc did 300,301,302
150/18:26:39 tc dlrs MEAS_SETUP TRW-ID HAS-EA-9.005
150/18:26:40 tc all Measurement HAS-EA-9.005
150/18:26:41 tc all HAS-EA-9.005 is an Effective Area measurement.
150/18:26:42 tc EKC 100 Orientation Move HRMA to (0,0).
150/18:26:43 tc EKC 101 OTG Insert
HETG
150/18:26:44 tc SAO 203 BND BND-H in fixed mode, synchronized to ACIS. I
ntegration time 5
150/18:26:54 tc SAO 204 Open all blades.
150/18:26:55 tc BALL 300 SIM-Z 190.5
150/18:26:56 tc BALL 301 FAM {0,0,0,0,0,0}
150/18:26:57 tc BALL 302 Duration Atomic time vector 501.495
150/18:26:58 tc BALL 303 Dither Dither file LISSAJOUS
150/18:26:59 tc ACIS 400 Setup (4, 2, 1, 0,501.495, imageID, biasID, chec
ksum) Do bias m
150/18:27:21 EKC tc got 100, 101
150/18:27:58 EKC tc did 100,101
150/18:28:14 SAO tc got 203,204
150/18:28:21 SAO tc did 203,204
150/18:28:36 ACIS tc
got 400
150/18:28:55 BALL tc got 300,301,302,303
150/18:29:30 BALL tc did 300,301,302,303
150/18:29:49 BALL tc ACIS set problematic will advise
150/18:30:05 BALL tc did 400
150/18:30:38 tc BALL 304 FAM Start Dither
150/18:30:51 BALL tc got 304
150/18:31:00 BALL tc did 304
150/18:31:08 tc SAO 205 HSA Open Shutters
150/18:31:31 SAO tc got 205
150/18:31:44 SAO tc did 205
150/18:31:58 tc ACIS measurement to begin in 10 seconds.
150/18:32:11 tc SAO 206 BND Start BND
150/18:32:12 tc ACIS 401 make measurement HAS-EA-9.005
150/18:32:13 tc dlrs MEAS_START HAS-EA-9.005
150/18:32:36 SAO tc got 296
150/18:32:45 SAO tc got 206
150/18:32:58 SAO tc did 206
150/18:33:24 ACIS tc got 401
150/18:33:33 ACIS tc did 401
150/18:33:43 ACIS tc fastest measurement on record
150/18:33:53 tc dlrs MEAS_STOP HAS-EA-9.005
150/18:33:54 tc SAO 206 BND Stop BND
150/18:33:55 tc SAO 207 HSA Close Shutters
150/18:34:11 SAO tc got 207
150/18:34:30 SAO tc did 207
150/18:36:06 SAO tc got 206.1
150/18:36:13 SAO tc did 206.1
150/18:36:21 tc BALL 305 FAM Stop Dither
150/18:36:22 tc all clean up from measurement HAS-EA-9.005
150/18:36:23 tc dlrs MEAS_CLND HAS-EA-9.005
150/18:37:05 ACIS tc ACIS QLC reports need to repeat measurement, please
adv
150/18:37:39 BALL tc got 305
150/18:37:50 BALL tc did 305
150/18:38:31 tc ACIS ok
.
150/18:39:01 ACIS tc ACIS QLC write tc cleaned up
150/18:39:02 tc all ****** End of HAS-EA-9.005*******
151/13:22:56 XSS tc_p wake up
151/13:23:11 tc XSS ok
151/13:31:22 tc dlrs MEAS_SETUP IXS-EE-1.007
151/13:31:23 tc all Measurement IXS-EE-1.007
151/13:31:24 tc all This measurement is an encircled energy meas. T seco
nds.
151/13:31:25 tc XSS Generator 01 Configure EIPS to run Mg-Ka set v6.4 wi
th c 140.217
151/13:31:26 tc XSS Filter 02 Filter 1 N/A Filter 2 Mg Thick 47.2.
151/13:31:27 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
151/13:31:28 tc EKC 101 Gratings No OTG in Place
151/13:31:29 tc SAO 200 Setup for IXS-EE-1.007
151/13:31:30 tc SAO XSS Setup Configure EIPS to run Mg-Ka set v6.4 with
curr
140.217
151/13
:31:31 tc SAO XSS Filter Setup Filter 1 N/A Filter 2 Mg 47.2.
151/13:32:06 tc all Everyone is ready for IXS-EE-1.007
151/13:32:17 tc SAO XSS Setup Configure EIPS to run Mg-Ka set v6.4 with
curr140.217
151/13:32:18 tc SAO XSS Filter Setup Filter 1 N/A Filter 2 Mg 47.2.
151/13:32:28 tc all Everyone is ready for IXS-EE-1.007
151/13:32:41 tc all Beginning IXS-EE-1.007
151/13:32:42 tc dlrs MEAS_START IXS-EE-1.007
151/13:32:43 tc SAO 201 Commence measurement IXS-EE-1.007
151/13:35:04 tc dlrs MEAS_SETUP IXS-EE-1.007
151/13:35:05 tc all Measurement IXS-EE-1.007
151/13:35:06 tc all This measurement is an encircled energy meas. T seco
nds.
151/13:35:0
7 tc XSS Generator 01 Configure EIPS to run Mg-Ka set v6.4 wi
th c 140.217
151/13:35:08 tc XSS Filter 02 Filter 1 N/A Filter 2 Mg Thick 47.2.
151/13:35:09 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
151/13:35:10 tc EKC 101 Gratings No OTG in Place
151/13:35:11 tc SAO 200 Setup for IXS-EE-1.007
151/13:35:12 tc SAO XSS Setup Configure EIPS to run Mg-Ka set v6.4 with
curr140.217
151/13:35:13 tc SAO XSS Filter Setup Filter 1 N/A Filter 2 Mg 4
151/13:35:58 tc dlrs MEAS_SETUP IXS-EE-1.007
151/13:35:59 tc all Measurement IXS-EE-1.007
151/13:36:00 tc all This measurement is an encircled energy meas. T seco
nds.
151/13:36:01 tc XSS Generator 01 Configure EIPS to run Mg-Ka s
et v6.4 wi
th c 140.217
151/13:36:02 tc XSS Filter 02 Filter 1 N/A Filter 2 Mg Thick 47.2.
151/13:36:03 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
151/13:36:04 tc EKC 101 Gratings No OTG in Place
151/13:36:05 tc SAO 200 Setup for IXS-EE-1.007
151/13:36:15 tc SAO XSS Setup Configure EIPS to run Mg-Ka set v6.4 with
curr140.217
151/13:36:16 tc SAO XSS Filter Setup Filter 1 N/A Filter 2 Mg 4
151/13:36:41 tc dlrs MEAS_SETUP IXS-EE-1.007
151/13:36:42 tc all Measurement IXS-EE-1.007
151/13:36:43 tc all This measurement is an encircled energy meas. T seco
nds.
151/13:36:44 tc XSS Generator 01 Configure EIPS to run Mg-Ka set v6.4 wi
th c 140.217
151/13:36:45 tc XSS Filter 02 Filter 1 N/A Filter 2 Mg Thick 47.2.
151/13:36:46 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
151/13:36:47 tc EKC 101 Gratings No OTG in Place
151/13:36:48 tc SAO 200 Setup for IXS-EE-1.007
151/13:36:53 tc SAO XSS Setup Configure EIPS to run Mg-Ka set v6.4 with
curr140.217
151/13:36:54 tc SAO XSS Filter Setup Filter 1 N/A Filter 2 Mg 4
151/13:37:02 tc all Everyone is ready for IXS-EE-1.007
151/13:37:09 tc all Beginning IXS-EE-1.007
151/13:37:10 tc dlrs MEAS_START IXS-EE-1.007
151/13:37:11 tc SAO 201 Commence measurement IXS-EE-1.007
151/13:37:15 tc all Measurement IXS-EE-1.007 completed.
151/13:37:16 tc dlrs MEAS_STOP IXS-EE-1.007
15
1/13:37:17 tc all Clean
up from IXS-EE-1.007
151/13:37:18 tc dlrs MEAS_CLND IXS-EE-1.007
151/13:37:30 tc all Measurement LHS-PI-1.004
151/13:37:31 tc all LHS-PI-1.004 is a PSF/Inner Core meas 10000 sec.
151/13:37:32 tc dlrs MEAS_SETUP TRW-ID LHS-PI-1.004
151/13:37:33 tc dlrs LHS-PI-1.004 is a PSF/Inner Core measurement.
151/13:37:34 tc EKC 100 Orientation Move HRMA to (0,0).
151/13:37:35 tc EKC 101 OTG InsertLETG
151/13:37:36 tc SAO 203 BND BND-H in fixed mode, not synch to ACIS. time
10000
151/13:37:37 tc SAO 204 HSA All blades open.
151/13:37:38 tc BALL 300 SIM-Z -250.1
151/13:37:39 tc BALL 301 FAM Position {0,0,0,0,0,0}.
151/13:37:40
tc BALL 302 Dither file letg_hrcs_psf
151/13:37:41 tc HRC Take HRC Image. Duration 10000
151/13:37:45 tc BALL 304 FAM Start Dither
151/13:37:49 tc SAO 205 HSA Open Shutter
151/13:37:53 tc HRC measurement to begin in 5 seconds.
151/13:38:01 tc SAO 206 BND Start BND
151/13:38:02 tc dlrs MEAS_START LHS-PI-1.004
151/13:38:03 tc HRC 500 make measurement LHS-PI-1.004
151/13:38:07 tc all making measurement LHS-PI-1.004, 10000 seconds.
151/13:38:12 tc all HRC is done with data collection on LHS-PI-1.004
151/13:38:13 tc dlrs MEAS_STOP LHS-PI-1.004
151/13:38:14 tc SAO 207 BND Stop BND
151/13:38:15 tc SAO 208 HSA Close all shutters
151/13:38:20 tc BALL
305 Stop Dither
151/13:38:21 tc all Hardware safe
151/13:38:22 tc all clean up from measurement LHS-PI-1.004
151/13:38:23 tc dlrs MEAS_CLND LHS-PI-1.004
151/13:38:31 tc dlrs MEAS_SETUP TRW-ID HAS-EA-9.005
151/13:38:32 tc all Measurement HAS-EA-9.005
151/13:38:33 tc all HAS-EA-9.005 is an Effective Area measurement.
151/13:38:34 tc EKC 100 Orientation Move HRMA to (0,0).
151/13:38:35 tc EKC 101 OTG Insert HETG
151/13:38:36 tc SAO 203 BND BND-H in fixed mode, synch to ACIS. Int time
501.495
151/13:38:37 tc SAO 204 Open all blades.
151/13:38:38 tc BALL 300 SIM-Z 190.5
151/1
3:38:39 tc BALL 301 FAM {0,0,0,0,0,0}
151/13:38:40 tc BALL 302 Duration Atomic time vector 501.495
151/13:38:41 tc BALL 303 Dither Dither file LISSAJOUS
151/13:38:42 tc ACIS 400 Setup (4, 2, 1, 0,501.495, imageID, biasID, chec
ksum) bias
151/13:38:49 tc BALL 304 FAM Start Dither
151/13:38:52 tc SAO 205 HSA Open Shutters
151/13:38:55 tc ACIS measurement to begin in 10 seconds.
151/13:39:08 tc SAO 206 BND Start BND
151/13:39:09 tc ACIS 401 make measurement HAS-EA-9.005
151/13:39:10 tc dlrs MEAS_START HAS-EA-9.005
151/13:39:24 tc all number 1
151/13:39:28 tc all number 2
151/13:39:30
tc all number 3
151/13:39:33 tc all number 4
151/13:39:35 tc all number 5
151/13:39:36 tc all number 6
151/13:39:37 tc all number 7
151/13:41:34 sstmgr tc XSS logged in
151/13:41:47 tc all number a
151/13:41:50 tc all number b
151/13:41:52 tc all number c
151/13:42:26 tc all number d
151/13:42:29 tc all number e
151/13:42:32 tc all number f
151/13:42:38 tc all number g
151/13:42:43 tc all number h
151/13:42:44 tc all number i
151/13:42:45 tc all number j
151/13:42:46 tc all number k
151/13:42:47 tc all number l
151/13:43:20 tc dlrs MEAS_SETUP IXS-EE-1.007
151/13:43:21 tc all Measurement IXS-EE-1.007
151/13:43:22 tc all This measurement is an encircled energy meas. T seco
nds.
151/13:43:23 tc XSS Generator 01 Configure EIPS to run Mg-Ka set v6.4 wi
th c 140.217
151/13:43:24 tc XSS Filter 02 Filter 1 N/A Filter 2 Mg Thick 47.2.
151/13:43:25 tc EKC 100 HRMA Orientation Move HRMA to (0,0).
151/13:43:26 tc EKC 101
Gratings No OTG in Place
151/13:43:27 tc SAO 200 Setup for IXS-EE-1.007
151/15:06:40 tc all Measurement LHS-PI-1.004
151/15:06:41 tc all LHS-PI-1.004 is a PSF/Inner Core measurement 10000 s
econd duration.
151/15:06:42 tc dlrs MEAS_SETUP TRW-ID LHS-PI-1.004
151/15:06:43 tc dlrs LHS-PI-1.004 is a PSF/Inner Core measurement.
151/15:06:44 tc XSS Gen 01 Configure EIPS to run Mg-Ka (6.4,140.217)
151/15:06:45 tc XSS Filter 02 Filter 1 N/AThick N/A Filter 2 Mg Thick 47
.2.
151/15:06:46 tc EKC 100 Orientation Move HRMA to (0,0).
151/15:06:47 tc EKC 101 OTG InsertLETG
151/15:06:48 tc SAO 203 BND BND-H in fixed mode. Integration time 10000
151/15:06:49 tc SAO 204 HSA configuration to be all blades
open.
151/15:06:50 tc SAO XSS Config EIPS to run Mg-Ka set volt to 6.4 with cu
rr 140.217
151/15:06:51 tc SAO XSS Filter 02 Filter 1 N/A Thick N/A Filter 2 Mg Thi
ck 47.2.
151/15:06:52 tc BALL 300 SIM-Z -250.1
151/15:06:53 tc BALL 301 FAM Position {0,0,0,0,0,0}.
151/15:06:54 tc BALL 302 Start dither using file letg_hrcs_psf
151/15:06:55 tc HRC HRC image(dum1,dum2,dum3,dum4)
151/15:06:55 tc HRC HRC image(dum1,dum2,dum3,dum4)
EOF reached
Back to the XTC Home Page
last updated 6/25/96.